Experimental Investigation on Chip-break Influenced by Cryogenical Cold Air jet

In machine cutting, the replacement of traditionalKGcutting solution with cryogenical cold air jet not only possesses a good cooling and lubricating efficiency, but also can avoid the occurrenceof environmental pollution. In order to clarify the manner and performance of discharged cutting chip under cryogenical cold air jet condition, an experiment was carried out for steel grade 45 in the dry and cryogenical cold air jet cutting comparatively. The effects of cryogenical cold air jet on the breaking of cutting chip are discussed. Experimental results reveal that, in the valid ranges of pressure and temperature, the cryogenical cold air jet can widen the chip broken region effectively. Different insufflating angle of cold air behaves different influence on the chip-break. From the experiment, it has been gained that the optimized jet insufflatingangle, temperature effecting range and pressure working range of cold air, which provides the foundation of industrial manufacturing.     

Study on Design of Bio-clean Operating Room

The design of Bio-clean operating room in modern hospital is quite different from that of traditional operating room. This paper discusses three aspects of Bio-clean operating room design: air clean standard and air purification, interior equipment system and interior finish. It is hoped that this discussion will conduce to later designs.     

Simulation of the penetration rate (ROP) of the air percussion drilling

It is difficult to calculate the penetration rate (ROP) of percussion drilling. In the early research, the empirical or semiempirical formulae of the ROP are derived from the laboratory or field data collected by the researchers. However, the ROP value of the formulae is not as accurate as that in the field. Benefiting from the dynamic model, the geometric structure model and the theory of the roller cone bit, the mathematical model of the hammer bit, the mathematical model of the true bottom hole and the mathematical model between the tooth and the rock of the hammer bit are established. Hence the ROP of the air percussion drilling can be predicted by simulation. Field tests show the models are reliable and the results are coincident with that in the field. The research can help to redesign the hammer bit and optimize the drilling parameters.     

发动机用平板型空滤器流动阻力特性分析和改进

为减小平板型空滤器流动阻力以增大进气量,对平板型空滤器流动阻力特性开展了实验研究,获得了空滤器流动阻力随流量变化的规律和阻力构成成分。阻力随流量的增大而加速增大,滤芯阻力约占整个空滤器阻力的一半,入口流量为120 m 3/h时,总阻力为915.3 Pa,滤芯阻力为426.4 Pa。在实验获得滤芯阻力参数的基础上,提出采用多孔介质跃升模型对平板型空滤器内部流场开展三维数值仿真分析,结果表明,仿真结果与实验结果比较吻合,最大误差为5.67%。滤芯阻力同样约占整个阻力的一半,另一半阻力主要为出口处阻力,其余壁面阻力约占15%。最后,在实验和仿真分析的基础上,提出了改进模型并进行了仿真分析。结果表明,改进模型阻力有较大程度的下降,入口流量为120 m 3/h时,总阻力为588.2 Pa,较原始模型下降了32.2%;增大空滤器流通横截面积是减小阻力以增大进气量的有效手段,改进空滤器壁面的平滑性是补充措施。     

A STUDY ON HEAT AND MOISTURE STATE OF HULL LAYER FOR THERMAL INSTULATION OF A COLD STORAGE

This paper analyses the thermal moist characteristics of the hull layer beside an air layer at lower temperature in an envelope for a cold storage and presents a new method of waterproof by air layer. With test data from engineering practice, the theory on the barrier of self moisture proof at the surface sublayer of the hull layer in an attic on a cold storage is proven. The dried zone about three phase point is confirmed. It is a new knowledge for thermophysics on thermal design of a cold storage with an optimum thermal performance.     

Application of Matter Element Analysis in Assessment of Ambient Air Quality

A new method for assessment of ambient air quality is proposed by using matter element analysis.This model is simple and reasonable in assessment.The practical example is given,and compared with other methods.     

浅谈筒仓的熏蒸方法及对筒仓气密性要求

文章介绍了目前对筒仓采用的几种熏蒸方法。对筒仓气密性对熏蒸效果的影响进行了讨论，并提出了对密封的补救建议。     

四气门柴油机进气门出口流速的分布

对四气门柴油机在两个进气道单独和同时开启的情况下，利用热线风速仪测量进气门出口全圆周速度分布，并通过动量矩流率的计算，分析了两个进气道气流相互影响的变化规律及其主要影响因素。结果表明，在进气过程中，两个进气道之间的气流相互影响，造成了两进气门出口速度的再分配，进而导致了缸内气流绕气缸轴线动量矩流率的变化。动量矩流率的总量与两气道单独开启时相比有明显减少，这是两气道的组合涡流比小于单独气道涡流比的主要原因。两进气道之间的干扰程度与作用结果取决于气道本身的结构形状和相对位置。     

射水抽气器最大吸气流量

为确定抽气器的工作范围,分析了单通道长喉管射水抽气器(即液气射流泵)在被吸气体为常压情况下最大吸气能力,认为喉管内液气两相混合的位置和流动状态是影响最大吸气流量的重要因素,喉管内发生两相临界流是有相变时抽气器的一种极限工况。采用一维流动公式计算了正常情况下最大吸气流量,试验数据说明在合理的抽气器尺寸情况下计算值与试验值一致。